Design of Ultra-wideband RF Front-end - read free eBook in online reader or directly download on the web page. Select files or add your book in reader. Download and read online ebook Design of Ultra-wideband RF Front-end write by Stanley Bo-Ting Wang. This book was released on 2005. Design of Ultra-wideband RF Front-end available in PDF, EPUB and Kindle.
Silicon-Based RF Front-Ends for Ultra Wideband Radios
Silicon-Based RF Front-Ends for Ultra Wideband Radios - read free eBook in online reader or directly download on the web page. Select files or add your book in reader. Download and read online ebook Silicon-Based RF Front-Ends for Ultra Wideband Radios write by Aminghasem Safarian. This book was released on 2007-12-28. Silicon-Based RF Front-Ends for Ultra Wideband Radios available in PDF, EPUB and Kindle. A comprehensive study of silicon-based distributed architectures in wideband circuits are presented in this book. Novel circuit architectures for ultra-wideband (UWB) wireless technologies are described. The book begins with an introduction of several transceiver architectures for UWB. The discussion then focuses on RF front-end of the UWB radio. Therefore, the book will be of interest to RF circuit designers and students.
Analogue RF Front-end IC Design for Ultra-wideband Implantable Wireless Body Area Network Radio
Analogue RF Front-end IC Design for Ultra-wideband Implantable Wireless Body Area Network Radio - read free eBook in online reader or directly download on the web page. Select files or add your book in reader. Download and read online ebook Analogue RF Front-end IC Design for Ultra-wideband Implantable Wireless Body Area Network Radio write by Ayobami B. Iji. This book was released on 2013. Analogue RF Front-end IC Design for Ultra-wideband Implantable Wireless Body Area Network Radio available in PDF, EPUB and Kindle.
Design of RF CMOS Front-End for Ultra-Wideband Wireless Receiver
Design of RF CMOS Front-End for Ultra-Wideband Wireless Receiver - read free eBook in online reader or directly download on the web page. Select files or add your book in reader. Download and read online ebook Design of RF CMOS Front-End for Ultra-Wideband Wireless Receiver write by 黃哲揚. This book was released on 2006. Design of RF CMOS Front-End for Ultra-Wideband Wireless Receiver available in PDF, EPUB and Kindle.
Design of a 3.1-4.8 GHZ RF Front-end for an Ultra Wideband Receiver
Design of a 3.1-4.8 GHZ RF Front-end for an Ultra Wideband Receiver - read free eBook in online reader or directly download on the web page. Select files or add your book in reader. Download and read online ebook Design of a 3.1-4.8 GHZ RF Front-end for an Ultra Wideband Receiver write by Pushkar Sharma. This book was released on 2006. Design of a 3.1-4.8 GHZ RF Front-end for an Ultra Wideband Receiver available in PDF, EPUB and Kindle. IEEE 802.15 High Rate Alternative PHY task group (TG3a) is working to define a protocol for Wireless Personal Area Networks (WPANs) which makes it possible to attain data rates of greater than 110Mbps. Ultra Wideband (UWB) technology utilizing frequency band of 3.168 GHz - 10.6 GHz is an emerging solution to this with data rates of 110, 200 and 480 Mbps. Initially, UWB mode I devices using only 3.168 GHz - 4.752GHz have been proposed. Low Noise Amplifier (LNA) and I-Q mixers are key components constituting the RF front-end. Performance of these blocks is very critical to the overall performance of the receiver. In general, main considerations for the LNA are low noise, 50 broadband input matching, high gain with maximum flatness and good linearity. For the mixers, it is essential to attain low flicker noise performance coupled with good conversion gain. Proposed LNA architecture is a derivative of inductive source degenerated topology. Broadband matching at the LNA output is achieved using LC band-pass filter. To obtain high gain with maximum flatness, an LC band-pass filter is used at its output. Proposed LNA achieved a gain of 15dB, noise figure of less than 2.6dB and IIP3 of more than-7dBm. Mixer is a modified version of double balanced Gilbert cell topology where both I and Q channel mixers are merged together. Frequency response of each sub-band is matched by using an additional inductor, which further improves the noise figure and conversion gain. Current bleeding scheme is used to further reduce the low frequency noise. Mixer achieves average conversion gain of 14.5dB, IIP3 more than 6dBm and Double Side Band (DSB) noise figure less than 9dB. Maximum variation in conversion gain is desired to be less than 1dB. Both LNA and mixers are designed to be fabricated in TSMC 0.18 [mu]m CMOS technology.
